Marvel 6CADM Průvodce řešením problémů stáhnout pdf (Strana 19)

temperature alarm will acvate at 9°C = (4 [set temperature] + 3

[Ahi] + 2 [hysteresis])

5) Relave Low Temperature Alarm (ALO): The

number of degrees C colder relave to set tem

perature that will iniate a low temperature

alarm. Once the compartment temperature exceeds the low

temperature alarm value, the control will delay AdL minutes

before iniang the alarm. See Alarm Delay secon below for

instrucons to set alarm delay. While ALo is displayed on the

screen, press and hold SET key to view the value of ALo. To

adjust the value, connue to hold SET then use the WARMER

and COLDER keys unl the desired value is shown on the screen.

Release the SET key to conrm the new seng. Factory default

value for ALo is -2.0°C.

Note: Seng ALo = 0 will disable the low temperature alarm.

No hysteresis value is added to ALo. For example, let set tem-

perature = 4°C, and ALo = -3. The low temperature alarm will

acvates at 1°C = (4 [set temperature] + -3 [ALo])

6) Alarm Delay (AdL): The number of minutes the

compartment temperature must be outside the

range specied by Ahi and ALo before a tempera-

ture alarm acvates. While AdL is shown on the screen, press

and hold SET key to view the value of AdL. To adjust the value,

connue to hold SET then use the WARMER and COLDER keys

unl the desired value is shown on the screen. Release SET key

to conrm the new seng. Factory default value for AdL is 60

minutes.

7) Total Operang Time of the Condenser Since

the Last Cleaning (cnd): The operang me of

the condenser since the last cleaning. The control

monitors the operang me of the condenser fan to determine

when the condenser is in need of being cleaned. While cnd is

displayed on the screen, press and hold SET key to view the value

of cnd. The value shown is the number of weeks the condenser

has been operang. To reset cnd, connue to hold the SET key

then press and release the ON/OFF key.

When the control recommends the condenser be cleaned, a

reminder will be displayed on the screen (see Alarm Codes.) To

clear the alarm code, reset the value in cnd following the instruc-

ons printed above.

8) Keypad Lockout Feature (Loc): This feature is

used to prevent incidental changes to the set

temperature, or accidentally turning the unit o.

While Loc is displayed on the screen, press and hold the SET key.

If “No” is displayed, Lockout feature is o, and all

keys are enabled. If “Yes” is displayed, Lockout fea-

ture is ON. The ability to turn the unit on and o, as well as the

ability to adjust set temperature will be disabled. To change the

keypad lockout seng, connue to hold the SET key, then use

the WARMER and COLDER keys to set the desired value.

APPENDIX A, ADDITIONAL MICROSENTRY™ FEATURES

Informaon Menu / Lockout Key

To access the informaon menu, press the SET key, and immedi-

ately release it.

In the informaon menu, a 2 or 3 digit code will be displayed

represenng each entry in the informaon menu. The rst code

displayed will be t1. With each sequenal press and release of

the SET key, the following codes will appear in this order: t1, thi,

tLo, Ahi, ALo, AdL, cnd, and Loc.

To view the value of each code, press and hold the SET key aer

the desired code is displayed. Addionally, the WARMER and

COLDER keys may be used to scroll through the menu. To exit

the informaon menu, press the ON/OFF key, or wait for several

seconds with no key presses.

1) Current Interior Temperature (tI): While tl is

shown on the screen press and hold the “SET”

key to display the current interior temperature.

2) Maximum Stored Temperature (thi): While

thi is shown on the screen, press and hold the

“SET” key to display the maximum recorded

temperature. The temperature is updated every 5 minutes. To

reset the maximum temperature; connue to hold the SET key,

then press and release the ON/OFF key to reset the maximum

temperature. The maximum temperature will be reset to the

current compartment temperature.

It is recommended that thi be reset aer the inial pull-down

(24 hours aer power on) to clear any residual values.

3) Minimum Stored Temperature (tLO): While tLo

is shown on the screen, press and hold the “SET”

key to display the minimum recorded tempera-

ture. The temperature is updated every 5 minutes. Connue to

hold the SET key then, press and release the ON/OFF key to reset

the minimum temperature. The minimum temperature will

be reset to the current compartment temperature. It is recom-

mended that tLo be reset aer the inial pull down (24 hours

aer power on) to clear any residual values.

4) Relave High Temperature Alarm (Ahi): The

number of degrees C warmer relave to the

set temperature that will iniate a high tem-

perature alarm. Once the compartment temperature exceeds

the high temperature alarm value, the control will delay AdL

minutes before iniang the alarm. See Alarm Delay secon

below for instrucons to set alarm delay. While Ahi is displayed

on the screen, press and hold SET key to view the value of Ahi.

To adjust the value, connue to hold SET then use the WARMER

and COLDER keys unl the desired value is shown on the screen.

Release the SET key to conrm the new seng. Factory default

value for Ahi is 2.0°C.

Note: Seng Ahi = 0 will disable the high temperature alarm.

The control’s 2°C Hysteresis value is automacally added to Ahi.

For example, let set temperature = 4°C, and Ahi = 3. The high

19

Marvel 6CADM Průvodce řešením problémů Strana 19

Komentáře k této Příručce

Marvel 6CADM Průvodce řešením problémů Strana 19

Komentáře k této Příručce

Související produkty a manuály pro ne Marvel 6CADM